¶ Safety Instruction
¶ EU DECLARATION OF CONFORMITY
Hereby, Shenzhen Creality Ecosystem Technology Co., Ltd declares that the radio equipment type [Creality Falcon T1] is in compliance with Directive 2014/53/EU.
¶ FCC compliance statement
1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
¶ ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1)This device may not cause interference.
(2)This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES‐003(B).
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1)L’appareil ne doit pas produire de brouillage;
(2)L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Cet appareil numérique de la Classe B conforme à la norme NMB‐003(B) du Canada.
Cet appareil est conforme à la norme RSS ‐ 247 d'Industrie Canada. Le fonctionnement est soumis à la condition que cet appareil ne provoque pas d'interférences nuisibles.
ISED Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements de la ISED établies pour unenvironnement non contrôé.
Cet équipement doit être installé et fonctionner à au moins 20cm de distance d’un radiateur ou de votre corps.
Cet émetteur ne doit pas être co-localisé ou fonctionner en conjonction avec une autre antenne ou un autre émetteur.
¶ EU Operating Frequency Range
Wi-Fi：
802.11 b/g/n20 2412–2472 MHz
802.11 n40: 2422-2462 MHz
5150-5850MHz
BLE: 2402–2480 MHz
EU Output Power:
Wi-Fi 2.4G≤20dBm
Wi-Fi 5150-5350MHz＜23dBm
Wi-Fi 5725-5850MHz＜14dBm
BLE≤20dBm
5GHz can be used indoor only.
¶ WEEE Declaration
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
¶ GPSR Safety Warning Declaration
1. This product is not a toy and not intended for use by children. For adult use only.
2. The appliance is suitable for moderate climates only.
3. The ventilation must not be impaired by covering the appliance with items such as newspapers, table cloths, curtains, etc.
4. Naked flame sources, such as candles, must not be placed on the appliance.
¶ RF Power Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
¶ Safety Instructions (Mandatory Reading)
Before operating this product, please read and understand all safety instructions and operating procedures. During operation, ensure that the product is correctly assembled and in normal working condition, and strictly follow all safety regulations.
¶ Laser Safety
This product is a Class 1 laser device，Consumer Laser Product
1. For Class 1 laser devices, observe the following operation guidelines: Do not operate the device with any parts removed. Do not activate the laser with the protective cover open. Ensure the protective cover is closed during operation.
2. Do not disable the open-cover stop function when replacing modules or observing the laser. If operation is required with the cover open, you must wear special laser safety goggles precisely matched to the equipment’s laser wavelength and ensure the equipment is in standby or non-processing state. For Class 4 laser machines, you must also wear dedicated laser safety goggles corresponding to the wavelength; ordinary sunglasses or prescription glasses are strictly prohibited as substitutes.
3. Inspect the safety goggles once a month. If scratches, cracks, decreased light transmittance, or loose frames are found, replace them immediately. Store the goggles in a dedicated case after use to avoid contamination or damage.
4. When processing metal, sharp materials, or high-temperature materials, must wear cut-resistant gloves or high-temperature resistant gloves. When processing materials that generate high-concentration smoke (e.g., wood or acrylic engraving), additionally wear an N95 or higher-grade dust mask.
¶ Environmental Safety
1.Although laser cutting does not normally cause combustion, certain materials (such as acrylic) may ignite under high temperatures. Always monitor the material during the cutting process. If flames appear, take immediate action to extinguish them.
2.Ensure that the operating environment is well ventilated, dry, and free from heat sources (≥60°C), dust, or flammable materials. The device is equipped with built-in temperature and humidity sensors and will automatically shut down if the limits are exceeded.
3.Laser processing may generate smoke or odors; operate the device only in a well-ventilated area.
4.Do not use this product during thunderstorms.
5.A suitable fire extinguisher must be readily available near the work area and should be maintained regularly.
¶ Electrical Safety
1.Use only the power cord supplied with this product. Substitution is not permitted.
2.When the device is powered on, do not touch electronic components (such as the motherboard or power interfaces) with your hands or tools.
3.Do not hot-plug the laser module or disassemble any electrical components while the device is powered on.
4.If the machine will not be used for an extended period, turn it off and disconnect it from the power supply.
¶ Operating Safety
1.Before using the machine, carefully read and fully understand all safety instructions and operating procedures. Inspect the device before each use. If any damage, malfunction, or abnormal behavior is detected, stop using the device immediately and perform necessary maintenance or repairs.
2.Regularly remove debris and residue from the machine to reduce the risk of fire. After powering off, use an anti-static brush and a dry cloth to clean the machine and the laser module. Do not use alcohol or other solvents.
3.Always connect the laser module’s silicone tube, regardless of whether air assist is used, to prevent contamination of the lens. If the tube becomes blocked, stop the machine immediately and clean it.
4.Do not touch moving mechanical parts or the laser module while the device is operating.
5.A laser-impermeable flat object (such as an aluminum alloy plate) must be placed beneath the processing material.
6.Do not process highly reflective materials directly. Doing so may damage or permanently impair the laser module. If such materials must be used, ensure the surface is blackened to reduce the risk of harmful reflections.
7.Do not leave the device unattended during operation.
8.Specialized laser protective eyewear must be worn during laser operation. Do not look directly at the laser spot.
¶ Restrictions for Specific Groups
1. Please make sure to operate the device with extreme caution in the presence of children. Minors must use it under adult supervision. Children under 10 years old are not permitted to access the device.
¶ Legal Liability & Compliance Requirements
1. Users shall comply with the laws, regulations, and professional ethics of the country/region where the device is located (used), and uphold safety obligations. Strictly prohibit using our company's products or equipment for any illegal purposes. Our company shall not be held liable for any legal consequences arising from violations.