400mm*415mm.
Semiconductor laser unit.
It will stop working. The machine will be initialized when powered on.
The imported image should be clear. Make sure that focusing correctly before engraving and the power and speed are appropriate.
Check that the screws are tight and the belt is not too loose or too tight.
The tightness of the belt is appropriate if the laser module can slide slowly on the X-axis profile perpendicular to the desktop by gravity, and any pulley in the laser module has no empty sliding.
Ensure that the material to be engraved is flat. Observe the gradienter on the machine to ensure that the machine is horizontal, and has been properly adjusted according to the operation method of the user manual.
5W---
Place the engraving material in the processing area before powering on, adjust the hand-tight nut on the right side of the laser module, and turn the fixed focus bar counterclockwise to make it contact with the surface of the material when it is naturally vertically downward. Then tighten the hand-tight nut and turn the focus bar clockwise until it is attracted by the magnet.
10W---
Please place the multi-level fixed focus bar between the laser module and the processed material. Follow the tips and make the bottom of the laser module contact with the corresponding surface of the multi-level fixed focus bar. Finally lock it with two hand screws on the right.
The laser may penetrate the material and damage the workbench (especially when cutting). It is recommended to place objects on the bottom that cannot be penetrated by the laser, such as stainless steel plates, aluminum alloy plates, etc.
1) Please check if the TF card is inserted. The machine reads the latest engraving file(.gcode/.gc) in the root directory of the TF card by default. It is recommended to delete other engraving files in the root directory.
2) The gcode file can only be generated by LightBurn. If gc file is generated by default, please modify the file suffix to gcode manually.
In preview mode and engraving mode, if the machine turns on it side or moves, it will turn off the laser. Motor stops moving, indicator light flashing, and buzzer emits alarm.
Solution: Please move the machine to its original position and press “Frame” or “Start/Pause” button on the control panel to continue previewing or engraving after clearing abnormality.
1) Check the power plug is plugged in properly.
2) Check the power outlet is properly powered.
3) Check the power switch, emergency stop switch and child lock on the machine are turned on.
The machine adopts the design of shading and eye protection, and integrates the MEMS attitude sensor. The laser module will stop working when the machine turns on it side abnormally. Even so, we still recommend that you wear goggles during working.
The machine has four limit switches. If the laser module exceeds the engraving area of the machine during working, the buzzer will beep and the machine stops working. At this time, it is necessary to adjust the position of the laser module and check the size of the graphics.
The engraved graphics will be deformed and dislocated obviously:like a circle changes into an ellipse.
It is convenient to measure the size of the object and assist in locating the engraving area.
Take out the filter cotton directly when powered off. Clean it with water, dry it and put it back (or replace it with a new one). Be careful not to touch the protective lens of the laser module.
It is due to the limited switch cannot be closed normally. Ensure that:
1. X direction:When the laser module moves to the end of the left side, the limited switch of X-axis can be closed normally;
2.Y direction:When the laser module moves to the end of the control box, the limited switch of Y-axis can be closed normally;
If the limited switches cannot be closed, check whether the wire is obstructing the movement of the laser module and the X-axis assembly first. Then reinstall the X-axis assembly to make it parallel to the front and rear X-axis profiles.
Engraving: Paper, Wood, Bamboo, Leather, Textile, Acrylic, Painted Metal, Plastic, etc.
Cutting: Paper, Wood, Bamboo, Cloth, Leather, Fabric, Acrylic, Plastic, etc.
Yes, but the radian of the material should not be too large. Otherwise there will be slight deformation.
Yes, but you need to apply anti-reflective material on the surface of the material before engraving to ensure the engraving effect and preventing the reflected light from damaging the laser module.
Materials with different colors have different optical properties. They have a difference in absorbing and reflecting the energy of laser. You can achieve a desired effect by adjusting the parameters.
Reduce the power appropriately and use the air assist from Creality.
1.Ensure that the machine and engraving material are parallel to the workbench; 2.Ensure that the protective lens of the laser module is clean; 3. Refer to the user manual and focus correctly; 4. Refer to the recommended parameters in TF card; 5. Gradually increase the number of passes or reduce the cutting speed appropriately;
The powerful and stable airflow can blow away the smoke and dust effectively during cutting, protecting the lens of the laser module and ensuring the stability of the laser energy. It can reduce the surface temperature of the cutting material quickly. Blow away the hot smoke and dust to keep material surfaces clean. Make the cutting edge smoother and more delicate.
It is recommended to use weak airflow when engraving, and strong airflow when cutting (the effect depends on the specific material).
LaserGRBL(Free)
LightBurn(Paid - 30 Days Free Trial)
LaserGRBL(https://lasergrbl.com/download/)
LightBurn(https://lightburnsoftware.com/pages/trial-version-try-before-you-buy)
LaserGRBL(bmp/png/jpg/gif/svg)
LightBurn(bmp/png/jpg/jpeg/gif/tif/tiff/tga/ai/pdf/sc/dxf/hpgl/plt/rd/svg)
The TF card comes with the machine. You can get more detailed tutorials from:
LaserGRBL(https://lasergrbl.com/usage/)
LightBurn(https://lightburnsoftware.github.io/NewDocs/)
Unzip the package and install the driver in the device manager manually.
1) Ensure that the Type-C data cable has the communication function and the end of the data cable connected to the computer is a USB-A interface.
2) Ensure that you have imported the Creality Falcon2.lbdev file successfully.
3) The corresponding COM port of the machine is not occupied.
4) If it still can't be connected, please record a video and tell the customer service your system information and the version of software.